NetBurner Community Forum

A community of NetBurner users gathering to discuss NetBurner hardware, software, design and projects
https://forum.embeddedethernet.com/

PK70 EX NPT looping

https://forum.embeddedethernet.com/viewtopic.php?t=2906

Page 2 of 2

Re: PK70 EX NPT looping

Posted: Thu Dec 06, 2018 11:29 am
by tgarvin
Tom. Not able to get to a prompt. It's stuck in a loop and I cannot break it.

This is what I'm seeing.

========================================================

Trap occured
Vector=05FMT =00 SR =2700 FS =00
Faulted PC = FF800348
D0:00000000 00465000 0000AAAA 00000001 00000000 5DFC8FAE CF206080 15001080
A0:4003AAAA FF810094 20000584 FF80016C FF80016C FF80036E 200007FC 20000634

Trap occured
Vector=05FMT =00 SR =2700 FS =00
Faulted PC = FF800348
D0:00000000 00465000 0000AAAA 00000001 00000000 5DFC8FAE CF206080 15001080
A0:4003AAAA FF810094 20000584 FF80016C FF80016C FF80036E 200007FC 20000634

Trap occured
Vector=05FMT =00 SR =2700 FS =00
Faulted PC = FF800348
D0:00000000 00465000 0000AAAA 00000001 00000000 5DFC8FAE CF206080 15001080
A0:4003AAAA FF810094 20000584 FF80016C FF80016C FF80036E 200007FC 20000634

Trap occured
Vector=05FMT =00 SR =2700 FS =00
Faulted PC = FF800348
D0:00000000 00465000 0000AAAA 00000001 00000000 5DFC8FAE CF206080 15001080
A0:4003AAAA FF810094 20000584 FF80016C FF80016C FF80036E 200007FC 20000634

Trap occured
Vector=05FMT =00 SR =2700 FS =00
Faulted PC = FF800348
D0:00000000 00465000 0000AAAA 00000001 00000000 5DFC8FAE CF206080 15001080
A0:4003AAAA FF810094 20000584 FF80016C FF80016C FF80036E 200007FC 20000634

Trap occured
Vector=05FMT =00 SR =2700 FS =00
Faulted PC = FF800348
D0:00000000 00465000 0000AAAA 00000001 00000000 5DFC8FAE CF206080 15001080
A0:4003AAAA FF810094 20000584 FF80016C FF80016C FF80036E 200007FC 20000634

Trap occured
Vector=05FMT =00 SR =2700 FS =00
Faulted PC = FF800348
D0:00000000 00465000 0000AAAA 00000001 00000000 5DFC8FAE CF206080 15001080
A0:4003AAAA FF810094 20000584 FF80016C FF80016C FF80036E 200007FC 20000634

Trap occured
Vector=05FMT =00 SR =2700
=============================================================================

Any ideas?

Re: PK70 EX NPT looping

Posted: Thu Dec 06, 2018 1:32 pm
by TomNB
That would explain the behavior of the link. The device is constantly resetting. If you cycle the power, do you see any messages before the trap messages occur?

Re: PK70 EX NPT looping

Posted: Fri Dec 07, 2018 8:16 am
by tgarvin
No I don't. it immediately starts displaying the traps.

Re: PK70 EX NPT looping

Posted: Fri Dec 07, 2018 8:41 am
by TomNB
In that case I think you will need to contact sales and submit it as an RMA. I can't think of anything that would cause that to happen.
All times are UTC-07:00
Page 2 of 2

Powered by phpBB® Forum Software © phpBB Limited