Search found 35 matches
- Wed Oct 10, 2012 11:03 am
- Forum: NetBurner Software
- Topic: SB70 still supported by software NNDK-2.6?
- Replies: 2
- Views: 2052
Re: SB70 still supported by software NNDK-2.6?
Thanks rnixon for your advice. I will keep it in mind.
- Tue Oct 09, 2012 2:35 pm
- Forum: NetBurner Software
- Topic: SB70 still supported by software NNDK-2.6?
- Replies: 2
- Views: 2052
SB70 still supported by software NNDK-2.6?
Hi, Today I got a newsletter from NETBURNER. It told me that there was a new release 2.6 of the NNDK. I downloaded it and looked at the release notes. I cannot recognize in these notes that it still supports the SB70. I have a PINK (SB70) module board REV 1.2 and a development kit with a board REV 1...
- Tue Oct 09, 2012 1:36 pm
- Forum: NetBurner Hardware
- Topic: SB70 misused as a GPIO device
- Replies: 7
- Views: 5579
Re: SB70 misused as a GPIO device
Thanks a lot for the information about the GPIO's.
I was a long time off the electronic grid. Nothing serious, I just had to make a choice between other interests above electronics.
Now I'm starting all over from scratch with this device again. I hope my old SDK (2008) will run on Windows 7, 64 bit.
I was a long time off the electronic grid. Nothing serious, I just had to make a choice between other interests above electronics.
Now I'm starting all over from scratch with this device again. I hope my old SDK (2008) will run on Windows 7, 64 bit.
- Thu Aug 27, 2009 2:17 pm
- Forum: NetBurner Hardware
- Topic: SB70 misused as a GPIO device
- Replies: 7
- Views: 5579
Re: SB70 misused as a GPIO device
No input?
- Sat Dec 06, 2008 4:39 pm
- Forum: NetBurner Hardware
- Topic: SB70 3rd serial port
- Replies: 6
- Views: 4855
Re: SB70 3rd serial port
Paul,
Thank you very much for the information.
Thank you very much for the information.
- Mon Nov 24, 2008 10:25 am
- Forum: NetBurner Hardware
- Topic: SB70 3rd serial port
- Replies: 6
- Views: 4855
Re: SB70 3rd serial port
Hi,
Yes, indeed there are 3 UART's reading the Freescale manual. I hope it can be found on the sb70 and accessed.
Regards,
SB70Koll
Yes, indeed there are 3 UART's reading the Freescale manual. I hope it can be found on the sb70 and accessed.
Regards,
SB70Koll
- Sun Nov 23, 2008 2:45 pm
- Forum: NetBurner Hardware
- Topic: SB70 3rd serial port
- Replies: 6
- Views: 4855
Re: SB70 3rd serial port
Hi Eric_v, Do you have new information about these pins? I see 3 pads but only two of them have connections to them. One of them have no connection on top or bottom or the board must be multilayered. Looking better to the SB72 docs I think there are only two port 0 and 1 and they are buffered by eit...
- Sun Nov 23, 2008 2:22 pm
- Forum: NetBurner Hardware
- Topic: Best source of SB70 GPIOs ?
- Replies: 2
- Views: 2717
Re: Best source of SB70 GPIOs ?
Hi, I looked at my SB70 (rev1.3) board and I do not find the pads. The location is stuffed with resistors. On the other hand I do see three pads above the MCF5270. One of them isn't connected, so there are maybe two pad that are connect to some in/output pin. The big disadvantage is that I did not f...
- Tue Nov 11, 2008 11:53 am
- Forum: NetBurner Hardware
- Topic: Digi WiFi modules..Has anyone tried to use one of these?
- Replies: 7
- Views: 4814
Re: Digi WiFi modules..Has anyone tried to use one of these?
Hi Chris,
Looked at some of their modules but could not find the $44 type. I read the WLNG-AN-DP101 sheet and saw that these devices need 3.3V supply so you might need to do some level shifting and/or need a second power supply (dc/dc) if the Netburner is powered with 5V.
sb70koll
Looked at some of their modules but could not find the $44 type. I read the WLNG-AN-DP101 sheet and saw that these devices need 3.3V supply so you might need to do some level shifting and/or need a second power supply (dc/dc) if the Netburner is powered with 5V.
sb70koll
- Tue Nov 11, 2008 11:01 am
- Forum: NetBurner Hardware
- Topic: Digi WiFi modules..Has anyone tried to use one of these?
- Replies: 7
- Views: 4814
Re: Digi WiFi modules..Has anyone tried to use one of these?
No Chris, I'm missing something Forgive me, I tangled up bluethooth with WIFI.