Search found 421 matches

by TomNB
Wed Jun 29, 2016 6:53 am
Forum: NetBurner Software
Topic: NNDK 2.5.2
Replies: 4
Views: 4014

Re: NNDK 2.5.2

Hi Frank, We do not have a revision that old up for download. You can request through support, or order a CD-ROM at this link: http://www.netburnerstore.com/embedded_ethernet_p/nndk-cdrom.htm Please specify the version in the comments section of the order. That said, I would agree with Paul that you...
by TomNB
Tue Jun 14, 2016 2:38 pm
Forum: NetBurner Software
Topic: Any documentation about the Virtual COMM port driver?
Replies: 21
Views: 21426

Re: Any documentation about the Virtual COMM port driver?

Glad its working :) But no netburner device is involved?
by TomNB
Tue Jun 14, 2016 12:57 pm
Forum: NetBurner Hardware
Topic: Configuration I/O
Replies: 1
Views: 5193

Re: Configuration I/O

Yes, that would be the Freescale mcf5441x data sheet:
http://www.netburner.com/mod54415/devel ... 900-1/file

Other than the irq pullups, which are there to help you avoid inadvertent irqs, the signals come direct from the processor.
by TomNB
Mon Jun 13, 2016 10:29 am
Forum: NetBurner Software
Topic: Any documentation about the Virtual COMM port driver?
Replies: 21
Views: 21426

Re: Any documentation about the Virtual COMM port driver?

Hello, I am not sure I understand the first part of your question. The virtual comm port driver should never be used with a real hardware comm port number. Lets take the case in which you create a virtual comm port that really is virtual, and not a h/w comm port. Lets say it is comm9. You then set t...
by TomNB
Wed May 25, 2016 3:15 pm
Forum: NetBurner Software
Topic: Using dual stack mode
Replies: 10
Views: 5607

Re: Using dual stack mode

Unlike IPv4 in which you specify a gateway either by dhcp or statically, in IPv6, the routers do that. So there is no analogy to an IPv4 gateway to route off network. On an IPv6 network you can set static addresses, no problem at all, an in fact all IPv6 devices will inherently have a link local add...
by TomNB
Mon May 23, 2016 3:00 pm
Forum: NetBurner Software
Topic: Using dual stack mode
Replies: 10
Views: 5607

Re: Using dual stack mode

Understanding the differences between v4 and v6 is going to be a very common question for everyone. It will take some background reading, but we are attempting to put together a document to help people get started. Attached is the first iteration of a document we would like to get feedback on and im...
by TomNB
Sat May 14, 2016 8:42 am
Forum: NetBurner Hardware
Topic: SB700EX and GPIO
Replies: 5
Views: 4205

Re: SB700EX and GPIO

Hello Sai Teja, We can not post confidential/copyrighted information such as NetBurner schematics and NetBurner system source code on a public forum. People posting their own source code is fine. As Paul suggested, if you can please use your account at http://support.netburner.com they can help you ...
by TomNB
Fri May 13, 2016 8:42 am
Forum: NetBurner Software
Topic: I2C (advanced) Read Issue
Replies: 9
Views: 5450

Re: I2C (advanced) Read Issue

Sorry, I scrolled to the last entry and saw your code post. Didn't realize you made two separate ones. What release are you using?
by TomNB
Thu May 12, 2016 4:00 pm
Forum: NetBurner Software
Topic: I2C (advanced) Read Issue
Replies: 9
Views: 5450

Re: I2C (advanced) Read Issue

Thanks Mark, but what I was really looking for was just a link to the thread so we can read the details.
by TomNB
Thu May 12, 2016 3:26 pm
Forum: NetBurner Software
Topic: I2C (advanced) Read Issue
Replies: 9
Views: 5450

Re: I2C (advanced) Read Issue

Hi Mark. Can you send a link to the post you are referring to?