Search found 25 matches
- Tue Jun 17, 2014 9:07 am
- Forum: NetBurner Software
- Topic: AES and Hardware
- Replies: 5
- Views: 3959
Re: AES and Hardware
Thanks!
- Tue Jun 17, 2014 8:45 am
- Forum: NetBurner Software
- Topic: AES and Hardware
- Replies: 5
- Views: 3959
Re: AES and Hardware
Does the AES code have extra cost?
- Tue Jun 17, 2014 8:36 am
- Forum: NetBurner Software
- Topic: AES and Hardware
- Replies: 5
- Views: 3959
AES and Hardware
Does the AES code listed in the NetBurner Security Libraries document use the encryption hardware in the processor?
Is AES included in the standard software or is it in the separate security package?
Thanks
Andy
Is AES included in the standard software or is it in the separate security package?
Thanks
Andy
- Sun Apr 07, 2013 7:57 pm
- Forum: NetBurner Software
- Topic: 5213 DMA caputre
- Replies: 1
- Views: 2102
Re: 5213 DMA caputre
Opps. As soon as a posted this I looked at the code and saw the mistake.
I had the vector set to tmr2. It should be:
SetIntc ((long)TMR3_isr, 22/*TMR3 interrupt*/, 1, 7);
Andy
I had the vector set to tmr2. It should be:
SetIntc ((long)TMR3_isr, 22/*TMR3 interrupt*/, 1, 7);
Andy
- Sun Apr 07, 2013 7:33 pm
- Forum: NetBurner Software
- Topic: 5213 DMA caputre
- Replies: 1
- Views: 2102
5213 DMA caputre
Hi, I'm trying to measure time intervals using the dma capture on the 5213. I suspect I might have the vectors wrong on the interrupt. It doesn't go to the interrupt routine because i watch pin 23 with a scope. INTERRUPT (TMR3_isr, 0x2700) { Pins[23]=1;//pulse to show we have been here Pins[23]=0; /...
- Tue Jan 22, 2013 9:23 pm
- Forum: NetBurner Hardware
- Topic: Pauls personal autopilot project board....
- Replies: 6
- Views: 5829
Re: Pauls personal autopilot project board....
Did you launch it?
- Thu Jan 17, 2013 10:02 pm
- Forum: NetBurner Hardware
- Topic: Pauls personal autopilot project board....
- Replies: 6
- Views: 5829
Re: Pauls personal autopilot project board....
I assume it would be good in a high power rocket. How big. How much. Im interested.
- Sat Jun 23, 2012 9:49 am
- Forum: NetBurner Hardware
- Topic: MOD54415 32 MB flash
- Replies: 4
- Views: 4311
Re: MOD54415 32 MB flash
Thanks for the suggestion but I think the 100 k will be fine with plenty of head room. If it was 10,000 cycles then I would have to think about this a little more.
Andy
Andy
- Fri Jun 22, 2012 3:54 pm
- Forum: NetBurner Hardware
- Topic: MOD54415 32 MB flash
- Replies: 4
- Views: 4311
Re: MOD54415 32 MB flash
I think 100k cycles will work for us. I assume the other chips will meet this requirement if you change vendor?
Thanks,
Andy
Thanks,
Andy
- Thu Jun 21, 2012 6:04 pm
- Forum: NetBurner Hardware
- Topic: MOD54415 32 MB flash
- Replies: 4
- Views: 4311
MOD54415 32 MB flash
What is the write cycle life on the 32 MB of flash memory on the MOD54415?
Thanks,
Andy
Thanks,
Andy