NANO54415

Discussion to talk about hardware related topics only.
fanat9
Posts: 56
Joined: Thu Apr 24, 2008 4:23 pm
Location: Boston
Contact:

Re: NANO54415

Post by fanat9 »

Nano54414 product page - Q3 2012.
seulater
Posts: 445
Joined: Fri Apr 25, 2008 5:26 am

Re: NANO54415

Post by seulater »

yes, but its not in the store to pre-order
User avatar
pbreed
Posts: 1080
Joined: Thu Apr 24, 2008 3:58 pm

Re: NANO54415

Post by pbreed »

It should be available in late Q2.
seulater
Posts: 445
Joined: Fri Apr 25, 2008 5:26 am

Re: NANO54415

Post by seulater »

ok, but when will the site have it for pre-order?
right now you can only pre-order the MOD54415 Ethernet Core Module, but not the nano.
bbracken
Posts: 54
Joined: Mon Jun 23, 2008 11:21 am
Location: Southern California
Contact:

Re: NANO54415

Post by bbracken »

I would be interested in this concept... particularly interested in display and audio.... the 2 things that are missing from the standard NetBurner boards.

bb
Ridgeglider
Posts: 513
Joined: Sat Apr 26, 2008 7:14 am

Re: NANO54415

Post by Ridgeglider »

Hi Paul: I know you're trying to minimize cost on the NANO54415, but as you consider its dev board, I'd encourage you to add SD support in either an SD or microSD adapter format, as well as including at least a few gpio LEDs and SW inputs like the ones that are on the DEV70 boards. If these can't be added to the dev board itself for cost reasons, another idea might be to offer a module that piggybacks onto all or part of the NB J2 connectors to add quick SD slot / LEDs / Switch inputs to any of you "MODd52xx" platforms.

The Nano54415 looks like a great platform!
User avatar
pbreed
Posts: 1080
Joined: Thu Apr 24, 2008 3:58 pm

Re: NANO54415

Post by pbreed »

I just sent the "new" dev board for the NANO out for fabrication.

It has 5 LED's 1 power, and 4 connected to GPIO.
It also has a micro SD connector.
All nano pins go to un-populated header pins.

Power via Jack or USB
Uart 0 -> USB (With a jumper to disconnect the RX line so you can do TTL over the header pins connector)
Uart 1 -> DB9(With a jumper to disconnect the RX line so you can do TTL over the header pins connector)
Uart 2 -> RS-485(With a jumper to disconnect the RX line so you can do TTL over the header pins connector)
CAN interface chip.

Paul
User avatar
Chris Ruff
Posts: 222
Joined: Thu Apr 24, 2008 4:09 pm
Location: topsail island, nc
Contact:

Re: NANO54415

Post by Chris Ruff »

Paul

did you remember to pull the two USB host pins out of the BGA for me?

Thanks

Chris
Real Programmers don't comment their code. If it was hard to write, it should be hard to understand
User avatar
pbreed
Posts: 1080
Joined: Thu Apr 24, 2008 3:58 pm

Re: NANO54415

Post by pbreed »

The USB host or Device interface is selectable by stuffing or not stuffing two resistors.
So the nano brings out the pins for either host or device USB.

The default stuffing will be device.

Paul
Ridgeglider
Posts: 513
Joined: Sat Apr 26, 2008 7:14 am

Re: NANO54415

Post by Ridgeglider »

Thanks! Sounds great!
Post Reply